Land Pride Lawn Mower ZXT54 Pro User Manual

ZXT Roll Over Protective Structure  
Assembly Instructions  
ZXT54 Pro & ZXT72 Pro Zero Turn Mowers  
Manual No. 357-274M  
Before You Start  
IMPORTANT: Your ZXT mower seat must have seat  
belt mounting holes in the back rest side plates. See  
Figure 1, balloon (B). If it does not, you will need to  
replace your seat with one that does.  
When you see this symbol, the subsequent  
instructions and warnings are serious - follow  
without exception. Your life and the lives of  
others depend on it!  
!
A detailed listing of parts for this accessory kit is  
provided on page 2. Use the list as a checklist to  
inventory parts received. Please contact your local Land  
Pride dealer for any missing hardware.  
IMPORTANT: Before you begin, read these  
instructions and check to be sure all parts and tools  
are accounted for. Please retain these installation  
instructions for future reference and parts ordering  
information.  
Initial Preparations  
1. Park unit on a flat level surface. Make sure blade  
engagement switch is (OFF), both control levers are  
fully (OUT), park brake is (ON) and switch key is  
turned (OFF) and removed.  
Your Roll Over Protective Structure is exclusively  
designed for your Land Pride ZXT mower. Please read  
these installation instructions and your ZXT mower  
Operator’s Manual thoroughly before beginning.  
Especially read information relating to safety concerns.  
Also included in the Operator’s Manual is important  
information on operation, adjustment, troubleshooting,  
and maintenance for this attachment (some manual  
sections do not apply to all accessories).  
A separate Parts Manual for the Zero Turn Mower is  
purchased from your nearest Land Pride dealer. Have  
the model and serial number of your Zero Turn Mower  
handy when placing an order.  
Manual Part Numbers:  
Operator’s Manual . . . . . . . . . . . . . . . . . 357-271M  
Parts Manual . . . . . . . . . . . . . . . . . . . . . 357-271P  
25974  
General Information  
Seat Belt Assembly (Deluxe Seat Shown)  
Suspension Seat Also Includes Seat Belt Mounts (B)  
Figure 1  
These assembly instructions apply to the following  
Accessory kits listed below:  
357-273A  
Folding ROPS W/Seat Belt, ZXT Series  
Seat Belt Assembly  
Tools required:  
Refer to Figure 1  
Safety Glasses  
1. Position seat belt (#1) with push button (A) on the right  
hand side so that the button is facing up when folded  
over onto the seat.  
Work Gloves  
Two 11/16" box end or open end wrenches  
Two 3/4" box end or open end wrenches  
2. Insert 7/16"-20 x 1 1/2" bolt (#5) through 7/16" flat  
washer (#4), seat belt (#1) and hole in mounting  
bracket (B).  
Assembly Instructions  
3. Secure seat belt with 7/16" flat washer (#4) and  
7/16" hex nylock nut (#3). Do not tighten nut.  
!
WARNING  
Do not modify the Roll Over Protective Structure in any way.  
This Roll Over Protective Structure has been designed  
specifically for this machine and any modifications can affect  
its performance in the event of a roll over.  
4. Rotate seat belt to the approximate angle shown and  
tighten nylock nut to 36 ft-lbs. of torque.  
5. Repeat steps 1 through 4 on the left hand side for the  
buckle end of the seat belt (#2).  
© Copyright 2008  
Printed  
3/31/08  
 
1

Kustom Music Mixer KPM8420 User Manual
KWC Plumbing Product K28H33500099 User Manual
Lenovo Camera Accessories T40 User Manual
Lenovo Personal Computer 08871BU User Manual
Lexmark All in One Printer X360 User Manual
Life Fitness Treadmill 93T XXXX 09 User Manual
Melissa Blender 246 008 User Manual
Mellerware Blender 85200 User Manual
Mercedes Benz Automobile MERCEDES BENZ S User Manual
MHP Printer 694C User Manual